Gorilla Super Glue

  • superglue

Talán már meg szerette volna venni, vagy talán csak titkon vágyott rá, nos most itt van! Bemutatjuk az új Gorilla Super Glue pillanatragasztót. Ez az első pillanatragasztó, amely erősen tart akkor is, ha erős ütésnek van kitéve. Ezt az Impacht-Tough formula gumirészecskéi teszik lehetővé. Egyszerűen szorítsa össze a ragasztandó felületeket 30-60 másodpercig.
ÜTÉSELLENÁLLÓ - a parányi gumirészecskék fokozzák az ütődésellenállást, ragasztás után gyorsan újra használható lesz a tárgy.
BESZÁRADÁSMENTES - a forradalmi beszáradásmentes kivitel egy beépített fém tűvel elkerüli a ragasztó eldugulását.
FELHASZNÁLÓBARÁT - a megvastagított formulának köszönhetően jobban folyik, így könnyebben ellenőrzés alatt tartható. 30-60 másodperc alatt megszárad, szorítás nélkül.
FELHASZNÁLÁSI TERÜLET:
A Gorilla Super Glue megragasztja a fát, fémet, kerámiát, számos műanyag fajtát, a gumit és még sok mást.


Gorilla Super Glue has tiny rubber particles that help secure your projects with a less brittle bond. This helps your project resist bumps, bangs and drops. We call it Impact-Tough™.

Gorilla Super Glue is a cyanoacrylate adhesive. Gorilla Glue is a polyurethane adhesive.

Gorilla Super Glue does not require extended clamping or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only.

Gorilla Super Glue is ideal for smaller repairs that require an instant bond and projects where clamping is not needed.

Gorilla Super Glue is easy to use. It dries in 15-30 seconds and no clamps are needed. Simply clean the surfaces of your project to rid of dirt, dust and grease. Apply a small amount of Gorilla Super Glue (more isn't always the better: use 1 drop per square inch). Then put your pieces together and hold for 15-30 seconds.

You can handle your project lightly after 1-5 minutes. 24 hours required for complete cure.

Yes, it will work on paper. Only apply a small amount. It is not acid free, therefore, not recommended for scrapbooking.

Gorilla Super Glue works well up to temperatures as high as 200-220ºF. However, too much exposure to extreme heat will cause the strength of the bond to be compromised. Likewise, too much exposure to water, especially warm water, can compromise the strength of the bond.

Gorilla Super Glue can typically be exposed to temperatures ranging from -65ºF to 200ºF without breaking down.

However, there can be variation to this range due to the way different substrates expand and contract in extreme temperatures.

To remove Gorilla Super Glue from your skin, soak the bonded area in warm soapy water or acetone (finger nail polish remover works well). The key is to be patient and NEVER pull the area apart.

Gently wiggle the area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind acetone can strip your skin of oils, so apply moisturizer after removal.

To remove Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. Keep in mind, acetone can mar the surface material or discolor fabric.

Gorilla Super Glue should not be used for intentional contact with the skin.

Each bottle of Gorilla Super Glue contains 15 grams of adhesive, though the bottle is only half full.

For high performance and usability the adhesive needs to be protected from air. One way keep the air out of the adhesive is by packaging in thick plastic bottles. If the bottle was completely full at 15g, and still the optimal thickness, it would be too hard to squeeze.

Moisture that gets into the bottle can cause the adhesive to set up and harden. The best practice is to immediately replace the cap and store in a cool, dry location.

There is a metal pin in the cap of Gorilla Super Glue that helps create a tight seal as well as keep the tip clear of dried adhesive.

We do not recommend storing your Gorilla Super Glue in the refrigerator. Because super glue can release gas, it should not be stored near food.

To remove Gorilla Super Glue from your skin, soak the bonded area in warm soapy water or acetone. The key is to be patient and NEVER pull the area apart.

Gently wiggle the area to allow the water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind acetone can strip your skin of oils, so apply moisturizer after removal.

If you are exposed to high quantities of super glue for long periods of time, it is best to wear safety glasses to avoid irritation. Should Gorilla Super Glue come in contact with your eyes, flush thoroughly for 15 minutes. Do not attempt to pull apart any bonded eyelid. Seek medical attention.

Do not induce vomitting.

Saliva will cause Gorilla Super Glue to polymerize, or harden, in mouth which means the adhesive usually doesn't make it into the throat or stomach.

If lips are bonded together, use warm water to gently separate. The enzymes in saliva will actually help to break the bond, so patience is the key. Do not use acetone or solvents on or near your mouth. Do not attempt to pull the area apart as this can tear the skin. Seek medical attention.

Gorilla Super Glue should be left out of reach of children and animals.

Gorilla Super Glue should be used in a well ventilated area. Inhalation may cause irritation to the nose, throat and repiratory tract. In the case of irritation, remove to fresh air.

 

Az Ön kosara üres.